Machine Recycling Discussion and Moderated Newsgroup > Separate Parts
> Electrical Parts
> West
> None yellowing clear gloss coat marine outdoors 1 gal
None yellowing clear gloss coat marine outdoors 1 gal
Aliphatic Polyurethane Dispersion
Clear None Yellowing Protective Coating
For Interior or Exterior Application
Zero VOC (volatile organic compound)
Cures to a high gloss none yellowing finish
Extreme durability for cyclic expansion and contraction
Excellent outdoor durability-gloss retention
Ambient or accelerated cure using forced air or heat convection
Outstanding adhesion to metals, plastics, concrete etc.
Retards fungal and algae growth in wood coatings
Resist dirt pick-up and easy cleaning
Spray Roller Coat or Brush Applied
CLICK ON THE PICTURE TO PAUSE OR PLAY SLIDESHOW
Excellent For Protecting Any Substrate From UV Damage And Mechanical Abrasion
Photographs Courtesy of Mr. Mike Huizenga President YaHu Inc. Manning, SC
was used as the concrete coating and 2 coats of MAX SEAL (roll coated) was applied as a protective top coat to reduce yellowing and impart slip resistance for foot and heavy equipment traffic.
MAX SEAL performs well as a floor sealant to protect against oil stains hot tire marking and maintains none surface slippery even wet
Applied on Wood, Metal, Plastic, Concrete or Stone Substrates
MAX SEAL is one of the newest technologies in polymer science that can be used for direct and prolonged outdoor exposure with minimal effect or loss of properties. It is truly one of the few materials that demonstrate low mechanical and aesthetic deterioration due direct UV exposure, environmental attack such as air borne pollutants, acid rain, heat aging and assaults from seasonal weather damage.
MAX SEAL is non-flammable, low skin irritant, and does not contain chlorinated or Ozone Depleting Chemicals (ODC).
MAX SEAL is ready to use directly from the container.
It can be further diluted with de-ionized water for microfilm applications or to increase open and flow out time.
MAX SEAL is a single component coating that can be brush, roll coater, or spray applied. When applied on porous material such as wood or concrete, the coating it will be tack free in less than 30 minutes and subsequent coats can be applied without further surface preparations. Upon cure the layers will cure to a unitize coating that will not peel between layers. Some surface preparation may be needed if coating is applied between long intervals.
The cure time is highly depending on ambient moisture or temperature.
MAX SEAL was formulated to comply with the new stringent air quality management laws for new coating applications. MAX SEAL exceeds the requirements of reportable volatile organic compound (VOC) to district air quality management agency, which makes it an excellent material for almost all types of industrial, commercial and architectural applications.
MAX SEAL is ready to use directly from the container.It can be further diluted with de-ionized water for microfilm applications or to increase open and flow out time.
MAX SEAL exceeds all Federal, State, County and Municipal Air Quality management regulations (AQMD), especially SCQAMD which is has the strictest air quality regulations
MAX SEAL is a single component water disperser polyurethane hybrid gloss coating has been used for:
Protective Coating For Leather
Paintings, Sculptures, Carvings Top Coat
Granite, wood marble, concrete, and synthetic materials (Corrian type) counter tops
Pottery And Carvings protective gloss coatings
Direct to metal anticorrosion coatings.
Commercial Restaurant Table And Countertops Top Coat and Refinishing
High Gloss Supple Fabric Coating
Outdoor furniture, wicker, plastics and metal for UV protective coating
Permanent Anti-Graffiti Coating
Fishing Rod Coating And Fishing Lure Coating
DO NOT APPLY MAX SEAL IN THICK FILMS AND IF THE RELATIVE HUMIDITY IS GREATER THAN 60%. MAX SEAL CURES VIA EVAPORATION OF THE WATER- BASED CARRIER SOLVENT. IT WILL APPEAR AS A WHITE MILKY COATING BUT WILL TURN TO A VERY TRANSPARENT CLEAR FINISH.
IF APPLIED DURING AT HUMID CONDITIONS, IT MAY TAKE LONGER TO CURE TO A DRY-TO-THE-TOUCH CONDITION AND REACT TO A FULLY CURED DURABLE COATING.
MAX SEAL exhibits high luster and gloss clear finish that is stain resistant to most materials such wine, iodine, paints, markers and other staining products. As an anti-graffiti coating, MAX SEAL can be directly applied on most materials and upon cure, graffiti removal solvents such as acetone, NMP or other non-chlorinated solvents can easily clean graffiti without damaging the coating. It is none-yellowing and inherently abrasion resistant.
MAX SEAL also demonstrates excellent adhesion to almost materials even 'tough to bond to surfaces' such polyethylene, polypropylene and other low surface tension substrates with minimal surface preparation. MAX SEAL can also be used as a clear rust proofing coating for metals such as steel, copper, brass and other soft metals that are susceptible to corrosion and oxidation.Apply MAX SEAL by brush, dip, roller, HVLP spray or airbrush. It has a very low viscosity making it suitable for coating intricate and high detailed patterns. Apply several thin coatings of MAX SEAL, allowing about 10 minutes before recoating. No sanding is needed in between coats. MAX SEAL will dry to the touch in less than 1 hour under normal ambient conditions but can be snap cured using forced air or convection drying ovens.
The exceptional toughness, flexibility and high luster finish makes MAX SEAL an ideal topcoat for wood and metal coatings projects. It demonstrates minimal flash rusting when applied directly on unprimed steel and excellent weather resistant and top coat protective properties on primed surfaces. Long-term outdoor exposure test of MAX SEAL coatings demonstrates excellent color stability and chalking resistance.
It exhibits common household cleaners resistance and can be further buffed to a mirror like finish using wax or polish.
Physical and Mechanical Properties
Less than 30 minutes dry to the touch
3 to 7 days for full cure at ambient conditions <30% relative humidity.
45 to 60 minutes full cure using forced air or convection drying
Weather Resistance (ASTM 1006)
Negligible loss in mechanical properties after 1 year of direct sunlight exposure
(< 1.2% loss in elongation and gloss)
Over 1,000 hours in accelerated weather chamber with less than 5% change in properties
FOR TECHNICAL SUPPORT PLEASE CALL
We are direct manufacture and formulators of high performance polymers for the industry for over 15 years. We have hundreds of large corporations that use our polymers in thousands of applications.
These are not extras, surplus, re-packs or old inventory. We purchase and mix our raw materials in large volumes and on demand. All kits are manufactured and packaged at the time of order so that we can guarantee fresh materials.
Please inquiry for volume discount.
If you have any questions or special applications, our staff polymer chemist will be more than happy to answer your questions.
FOR MORE PICTURES OF MAX SEAL APPLICATIONS, PLEASE VISIT OUR PHOTO SHARING SITE AT:
The user should thoroughly test any proposed use of this product and independently conclude satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval.
The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtain through publish information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.
There is no warranty of merchantability of fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period.
PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind.
Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user
