Machine Recycling Discussion and Moderated Newsgroup > Full Machines
> Complete Machines
> Kolpak walk-in cooler, 6'6"X6'6" easy to assemble kit
Kolpak walk-in cooler, 6'6"X6'6" easy to assemble kit
This freezer is self contained, you can install yourself, it is pre charged and ready to be up and running hours after you receive it. You do not have to pay a Rerfrigeration Technician $500-$900 to install
Refrigeration Unit - Cooler Serial Number- M280380
In the picture you see both the walk in cooler and walk in Freezer. Please make sure that you know that this is only for the Cooler side.
If you are local to Denver you can pick up at our 15,000 sq ft warehouse., Call "Bennett" for Details.
The cooler is in great shape. There is a little rust on the floor but that is it... This is a Great DO-IT-Yourself Freezer as the Mechanical is ready to install on the top of the box. It has easy to assemble cam lock construction and can be installed just anywhere since it is 115v.
We have thousands of references that we have sold equipment to, from our website at www.brrr.cc. Check us out.
We have been in business for over 20 years.
We have many additional items on our website that we have sold all over the world.
We have many other cases too in all brands and configurations, give us a call at (***)-441-2596 and one of our seasoned refrigeration specialists will help you find exactly what you are looking for.
We have a HUGE warehouse located in the Denver area and we can arrange local delivery and set up the equipment if that is a way that you want to go.
Looking for any of the following? We carry new and used....
Click on the link and it will take you to our website...
Cold Storage Room, Glass Doors
Cold Storage Room, Solid Doors
Cold Storage Room, Walk-In Freezer
Cold Storage Room, Walk-In Refrigerator
Lab & Pharmacy Chromatography Refrigerators
Lab & Pharmacy, Explosion Proof
Lab & Pharmacy, Flammable Storage
Lab & Pharmacy, Ultra Cold Units
Call us today at (***)-441-2596 or in the Denver area at (***)-750-2777.
Check us out online www.brrr.cc
I copied this from manufacturer Kolpak website:
Walk-in coolers or freezers provided under this portion of the specifications shall be prefabricated, of modular
design and construction. They shall be designed to allow convenient and accurate field assembly and future
enlargement by the addition of panels.
Standard wall, ceiling and floor panels shall be nominal 2' and 4' in width and shall be interchangeable with like
panels. Standard heights of walk-ins shall be. Corner panels shall be 90-1/4 angles with actual 12' exterior
horizontal measurements. Nominal 1' and 3' panels shall be used if required to meet job site conditions. Available
heights with floor or 4" vinyl screeds: 7' 6" 8' 6", 9' 6", 10' 6", 11' 6", 12' 6". Available heights without floor, with 1
1/2" vinyl screeds: 7' 4", 8' 4", 9' 4", 10' 4", 11' 4", 12' 4". Panels shall consist of foamed - in - place urethane
insulation, sandwiched between interior and exterior metal "skin" which has been die-formed and gauged for
uniformity in size. Edges of panels shall be foamed - in - place tongue and groove with locking facilities foamed - in
- place at time of fabrications.
Floor Panels: Panels shall be fabricated similar to other panels, designed to readily withstand uniformly
distributed loads of 700 lbs. per square foot. Floor (will/will not) be recessed. Floor (will/will not) be covered
by the tile and grout, or concrete wearing floor.
Floorless: Provide 1-1/2" high or 4" high Temp-Guard vinyl screeds. Screeds must be coved on both sides
and sit flat on the floor. Screeds shall be nailed or lag fasteners shall be allowed. Wall panels lock to
Each panel shall be filled with rigid "Foamed-In-Place" urethane having a thermal conductivity (K factor) of .133
BTU/hr./ft squared per degrees Fahrenheit/inch and an overall coefficient of heat transfer (U factor) of not more
than .03. "R" factor shall be 31 or greater. Insulation shall have a 97% closed cell structure. Overall thickness shall
Panel skins, standard models, standard and optional metal finishes are as follows (Specify one or a combination of
Exterior and Interior walls shall be one of the following:
1. .26 gauge stucco-embossed Galvalume steel.
2. 032 stucco-embossed aluminum.
3. 22 gauge Type 304 stainless steel, #3 finish.
4. 20 gauge Type 304 stainless steel, #3 finish.
5. 26 gauge stucco-embossed Galvalume pre-painted white.
6. Other metal finishes and paint colors available. Consult factory.
Exterior floor and ceiling shall be 26 gauge Galvalume steel on all walk-ins, unless otherwise called for.
Interior floor shall be one of the following:
4. 16 gauge galvanized steel (tile and grout applications)
Assembly of walk-in shall be accomplished by Posi-Locs. Posi-Locs shall be foamed-in-place and activated by a
hex wrench provided by the manufacturer. Access ports to locking devices shall be covered by snap caps. Access
ports shall be on interior to allow assembly of walk-in from the inside.
NSF listen gaskets shall be foamed-in-place to the male side of all panels, on both interior and exterior. Gaskets
shall be impervious to stains, greases, oils, mildew, etc.
Each walk-in shall be fitted with one standard 34" x 78" swing-type entrance door. The door shall be flush type,
finished in and out to match the wall in which located. Doors and door section shall be listed by Underwriters
Laboratories and equipped with the following:
Door shall be equipped with magnetic gasket, Posi-Seal door closure and latch. Hardware has provisions
for locking and a safety release which prevents entrapment of personnel within the box
Door shall be self-closing with two strap-type, cam-lift hinges.
Door jamb shall be made of Fiberglass Reinforced Plastic. An isolated, low wattage heater strip covered by
magnetically attracting stainless steel shall be fitted onto this jamb (freezer only). This strip shall provide
perfect sealing of magnetic gasket and prevent frost and condensation build-up.
Each entrance door section shall be provided with an incandescent type vapor-proof light, pilot light switch
and conduit between switch box and outlet box. Concealed wiring shall be standard on each entrance door
A threshold with non-skid striping shall be provided with each door section. Heater wire shall continue
beneath the threshold (freezer).
A 2" dial thermometer shall be included with each door section to indicate inside temperature.
Fabrication and finish of partition walls shall be the same as the walk-in walls and shall lock into wall, ceiling,
and/or floor panels, with Posi-Loc assemblies. Tongue and groove foam fabrication shall provide the thermal break
between cooler and freezer compartments. Wall "T" panels shall be 23" x 12" symmetrical tee. Heater wires not
All walk-ins shall be fabricated to comply with National Sanitation Foundation No. 7. The NSF label shall be affixed
to the interior door pan. All interior corners, including floor shall be coved.
A Tri-Action air vent shall be provided to equalize pressure between the interior and exterior, caused by sudden
temperature changes due to door openings and evaporator defrosting. The vent shall be heated to prevent
moisture and/or frost accumulation (required for freezers).
A complete set of installation instructions shall be included with the walk-in. These instructions shall cover the
erection and assembly of the walk-in, and the installation of refrigeration systems. A floor plan print shall be
Condensing units shall be fully hermetic or semi-hermetic type. Refrigerant shall be R-22 or R-404A unless
otherwise specified. Condenser shall be air-cooled or optional water-cooled. Condensing units shall be factory
assembled and UL or ETL listed. Evaporators shall be forced air type. Air discharge shall be parallel to the walk-in
ceiling. Fan motors, guards multi-fin and tube-type coil, shall be housed in heavy gauge aluminum. Unit shall have
drain pan with suitable drain pipe fitting. Freezer evaporators shall have and automatic electric defrost system
including heater, time clock, fan delay control, and heated drain pan. Defrost shall be time initiated and
temperature terminated with built-in fail-safe control. All evaporators shall be UL listed. All systems include pump
down cycle to provide additional protection against unwanted refrigerant flow.
These basic components shall be supplied by Kolpak as one of the following systems:
"CS" Self-Contained Top Mounted
"SS" Self-Contained Side Mounted
"PCL" Pre-Charged Lines (Remote)
"PR" Pre-assembled Remote See Refrigeration Systems for details on above systems.
For air-cooled condensing units installed outdoors (to -20 F) where sub-zero ambient temperatures prevail for
sustained periods - include crankcase heater, head pressure control, and rainproof housing.
For below -20 F ambient temperatures, consult factory.
Installing contractor shall provide suitable drain lines from all evaporators. Drains shall be trapped outside the
walk-in. Freezer drains shall be copper tubing and shall be heated and insulated to prevent freeze-up. All plumbing
to be in accordance with local codes. Drain line heater kits available from Kolpak in 6', 2' or 18' lengths.
Required if job site does not have a floor drain near the walk-in. An electric condensate evaporator shall be
provided for wall mounting on exterior of the walk-in. 115-60-1 AC continuous service voltage required.
Top-mounted coil system can be used to provide more useable storage space. Coil is positioned above interior of
